Reset Car Battery - How to Discuss

Reset Car Battery

I want to reconfigure my car's on-board computer, they told me to disconnect both battery terminals. Why not just one? ۔

I am an electrical engineer and I know that electrons need 2 connections for the flow of electricity.

Only answer if you have electronic knowledge.

You are right sir. Many people think they know cars work, but they don't. Electronic theory is usually its weak point.

Removing the battery or not removing the code and the duration of shutdown depends on the manufacture and year of the vehicle. New cars often remember these things. Like a PC, you won't lose all your files just because you log out.

Another consideration is whether or not you have a factory anti-theft radio. In that case, you'll need a reset code to make it work. Even if you have an old style computer, you will forget the best settings you learned to run your N during your best performance. After doing so, do not go to the top of the semifinals for a while until the computer has a chance to re-learn these settings. MDR

Always disconnect the negative pole first and then reconnect or remove the negative pole if necessary. This is because if you are doing this your key hits the chis, it is not pointing to a negative but to a srt number. The change is positive.

To rearrange the information stored on the onboard diagnostic computer, you need to remove the negative pole. The reason is that, after all, everything is connected to the earth. At least that's the theory I learned from technical school.

The recommended time is usually 10 minutes and all the codes are deleted. But here is the PCM (Power Control Module) that works. Depending on which system is difficult, there is a learning cycle. Most vehicles learn the limits of driving and keep them for reference. Sometimes when someone else is driving, the driving style is different and the signal light comes on. The pattern is broken and the computer needs to re-learn the new pattern.

If the indicator light comes on immediately, you have trouble closing the input circuit. This circuit only receives information from various sensors, especially from the temperature sensor, when the car is cold. When the car is at operating temperature (open circuit), many other sensors are included and proper diagnosis should be made through the diagnostic device.

If the indicator light flashes, it means that the PCM is in clean mode and the vehicle should be taken to the workshop immediately.

Note: For best performance when restarting the car computer. Leave the negative pole disconnected for 10 minutes (make sure your car doesn't have radio code, and if it does, it does). After replacing the battery, run 5 to 10 miles as if you have stolen it. This will set the internal parameters in PCM for better acceleration and faster response.

This page can help you.

D:

I want to reconfigure my car's on-board computer, they told me to disconnect both battery terminals. Why not just one?

I am an electrical engineer and I know that electrons need 2 connections for the flow of electricity.

Only answer if you have electronic knowledge.

Reset Car Battery

Reset Car Battery

I want to reconfigure my car's onboard computer, they told me to disconnect both battery terminals. Why not just one? 3

I am an electrical engineer and know that electrons need 2 connections for the flow of electricity.

Only answer if you know about electricity.

You are right sir. Many people think they know cars work, but they don't. Electrical theory is often its weakness.

Whether you remove the battery or not, the code will be erased and the duration of shutdown will depend on the vehicle and year of manufacture. New cars often remember these things. Just like a PC, just because you log out doesn't mean you lose all your files.

Another consideration is whether or not you have a factory anti-theft radio. In that case, you'll need a reset code to make it work. If you have an old-fashioned on-board computer, you'll forget about the ideal settings you learned to run your ■■■■■ on the go. After doing this, do not go to the top of the semifinals for a while until the computer has a chance to re-learn these settings when you do this. MDR

Always disconnect the negative pole first and then reconnect or remove the negative pole if necessary. This is because if your key touches the chis while you are doing this, it points to the whole srt, not the negative. In the positive srt.

To rearrange the information stored on the onboard diagnostic computer, you need to remove the negative pole. The reason is that ultimately everything is connected to the earth. At least that's what I learned from technical school.

Normally the recommended time is 10 minutes and all codes will be deleted. But here PCM (Power Control Module) works. Depending on which system is difficult, there is a learning cycle. Most vehicles learn the limits of driving and keep them for reference. Sometimes when someone else is driving, the driving style is different and the signal light is on. The pattern is broken and the computer needs to re-learn the new pattern.

If the indicator light comes on immediately, you have trouble closing the input circuit. This circuit only receives information from various sensors, especially the temperature sensor, when the vehicle is cold. When the car is at operating temperature (open circuit), many other sensors are included and proper diagnosis should be made with the diagnostic tool.

If the indicator light flashes, it means the PCM is in clean mode and the car should be taken to the workshop immediately.

Note: For best performance when restarting the car computer. Leave the negative pole disconnected for 10 minutes (make sure your car's radio doesn't have the code, and if it does, it does). After replacing the battery, run 5 to 10 miles as if you have stolen it. This will set the internal parameters in PCM for better speed and faster response.

This page can help you.

D:

I want to reconfigure my car's onboard computer, they told me to disconnect both battery terminals. Why not just one?

I am an electrical engineer and I know that electrons need 2 connections for the flow of electricity.

Please reply only if you have knowledge of electricity.

Reset Car Battery