What Does Center to Center Mean

Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.

How do you measure for cabinet knobs?

To accurately measure existing fixing centers, open your kitchen door or drawer and measure the distance between the center of each screw. This measurement should be used when specifying your new handles.

How do you measure center to center for cabinet pulls?

To find the center-to-center measurement, use a screwdriver to remove your current pulls, then take a ruler or measuring tape and measure from the center of one screw hole to the center of the other screw hole.

How do you measure cabinet hardware?

Center-to-Center– the distance from the CENTER of one screw hole to the CENTER of the other screw hole. This is the standard industry measurement for sizing cabinet handles. Overall Length– the distance from one end of the pull to the other end.

How big should dishwasher pull be?

Smaller Appliances (i.e. Dishwasher Or Fridge Drawers): 12 inch long appliance pulls are typically large enough. Larger Appliances (Refrigerator Or Freezer Columns): 18 inches or longer appliance pulls can look most proportionate.

Should cabinet pulls be vertical or horizontal?

Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.

What does center to center mean in cabinet pulls?

The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.

Should drawer handles be centered?

As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.

What size should drawer pulls be?

There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.

How do you measure kitchen pulls?

Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.

How do you find the center between holes?

If the holes are the same size, measure from the same edge (left edge to left edge or right edge to right edge) of the holes. That will be the same distance as center-to-center. Use a trusted tape measure starting at 10″ (not at the end hook). Measure and subtract 10″.

Where should knobs go on cabinets?

Cabinet knobs should be installed on the stile opposite the hinges. The general rule is to place a knob 2 1/2″ – 3″ from the corner of the door. For upper cabinets, install knobs in the bottom corners of the door. For lower cabinets, place them in the upper corners.

Should I use knobs or pulls on kitchen cabinets?

There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.

Do you put pulls on fake drawers?

I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.

Can you mix knobs and pulls on kitchen cabinets?

Yes, you can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.

Can you mix drawer pull sizes?

There’s no “rule”, it’s a matter of looking at as many kitchens as possible and figuring out the look you prefer. I also used a variety of sized pulls on drawers of different widths, and used Restoration Hardware.

How long should appliance pulls be?

Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.

What size should kitchen knobs be?

Knobs that are 1 ¼” to 1 ⅜” are standard for most applications. Any knob that is 1 ½ inches or larger is generally used on larger cabinets or if someone is really trying to make their hardware stand out and look more dramatic.

What does CC mean in handles?

CC stands for center to center, ie. the distance between the center of one screw hole to the center of the other screw hole. If your kitchen is from the 80s or newer, it will be very easy to change the handles on your cupboards or drawers.

How do you choose cabinet pulls size?

There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.